3kw 1500rpm Three Phase Closed Loop Servo Stepper Motor Drives For
UV Flatbed Printer
Closed Loop Servo Stepper Motor Drives
AC Power 3KW
Three Phase 380V
Modbus / CanOpen / EtherCAT
Location / Speed / Torque Control Mode
17/23bit Tamagawa absolute encoder;
|Product Name||Closed Loop Servo Stepper Motor Drives|
|Encoder||17/23 bit Tamagawa absolute encoder|
The panel contains 8 buttons and 5 digital tubes.
Only 5 of the 8 buttons can be used, and the remaining 3 buttons
The general functions of the five buttons are shown in the table
|Key Name||Key function|
|PAR/ALM||mode switch, return to the previous menu|
|▲(add)||increase flashing bit value of the LED digital tube|
|▼(dec)||Decrease flashing digit value of the LED digital tube|
|STOP/RST||Moves the blinking LED tube to the left; checks the high value of
longer than 5 bits; Fault reset;execute Fn function
|RD/WT||read/write parameter values;enter fn page|
● Install the driver on a dry and sturdy platform. Maintain good
heat dissipation during installation and maintain good grounding.
● Please install in the specified direction to avoid malfunction.
● When installing, please ensure that the servo driver is kept at a
distance from the inner surface of the cabinet and other machines,
otherwise it may cause fire or malfunction.
● When installing, do not block the suction and exhaust ports, and
do not allow foreign objects inside the
product to enter, otherwise it may cause malfunction or fire due to
aging of internal components.
● Do not place heavy objects on or under this product as this may
result in injury.
● Please install in the following environment:
1.places without direct sunlight;
2.Locations where the ambient temperature is in the range of 0 ° C
to 55 ° C;
3.Relative humidity in the range of 0% to 95%, and no condensation;
4.Locations free of water droplets, vapors, dust and oily dust;
5.Locations where there is no high heat device;
6.Non-corrosive, flammable gas and liquid sites;
7.It is not easy to splash water, oil and medicine;
8.places that are not exposed to radioactive radiation;
9.Strong and vibration-free places;
10.Locations where there is no electromagnetic noise interference.
Packing and Shipping
|Packing details of Servo Drive|
|Packing details of Motion Controller|
|Products||VA Motion||VA Expansion||VE Motion||VE Expansion(32)||VE Expansion(76)|
|Quantity||1-5 kits||50-100 kits||200-500 kits|
|Delivery time||Within 3 days||5-10 days||15-25 days|
1. For small order we always can delivery out within 1 week.
2. Our products can be shippied via Air, Land or Sea.
|Satandard Spare Parts||Power terminal||Adapt to E1,E2 structure drive|
|Cn3 encoder plug||Encoder plug on the driver side|
|Cn4 control terminal plug||Input/output signal terminals,user wiring|
|Encoder connection line||The standard cable length is 3, 5, 8, 10, 13, 15 meters, according
needs Provide independent connector
|Power line||The standard cable length is 3, 5, 8, 10, 13, 15 meters, according
needs Provide independent connector
|Drive monitoring line||Connect and adjust the software for remote monitoring and firmware
|Purchasing Spare Parts||USB to RS232 Adapter cable||If necessary, self purchase|
|Ethernet communication line||If necessary, self purchase|
1. CE (EU Safety Standard);
2. IEC/EN61800-5-1:2007 (Safety requirements for electrical,
thermal and energy in Section 5-1 of the
variable speed electric driver system), corresponding to the
national standard GB12668.501-2013;
3, IEC / EN61800-3: 2004 + A1 (speed control electric driver system
part 3 electromagnetic compatibility
standards and its specific test methods), corresponding to the
national standard GB12668.3-2012.